Extractor

[TonyChopper]

Can ask or not how much for a new 5zigen extractor if buy from N1 racing?
My friend got 1 custom made extractor for sell only rm300 brand new.. I checked the inner surface very kilat dun have carbon "shit".. and the design is copy mugen one... basically the extractor cantik la so not sure to buy a jasma one or the custom made one..
Any1 got suggestion?

 

[zero4]

Can ask or not how much for a new 5zigen extractor if buy from N1 racing?
My friend got 1 custom made extractor for sell only rm300 brand new.. I checked the inner surface very kilat dun have carbon "shit".. and the design is copy mugen one... basically the extractor cantik la so not sure to buy a jasma one or the custom made one..
Any1 got suggestion?

jasma one loh, weilding points nicer, quality also different

 

[TonyChopper]

5zigen brand new from N1 racing how much?

 

[zero4]

i dunno woh, anyone here knows?

 

[TonyChopper]

Mmm.. 1 more question.. My piping now is 2 inch straight flow... quite shiok already since removed the cat.. isit necessary to make it 2'3 inch.. my friend say 1.8 car must do 2'3...
Thx zero4.. ^^
anyone know how much 5zigen extractor cost? new one..

 

[HanafyEG]

5zigen brand new i think is about rm1800..it was very good..u free2 go see for urself la the price and the thing...
i used it before..then i change to even better one..toda..toda was superb man!

 

[HanafyEG]

Mmm.. 1 more question.. My piping now is 2 inch straight flow... quite shiok already since removed the cat.. isit necessary to make it 2'3 inch.. my friend say 1.8 car must do 2'3...

2.2 is for 1.6 dohc vtec...so 2.3 would be ok for 1.8 dohc vtec, depends on ur mod also..big hi compression pistons and hi cams..or 2L block..then u need 2.5

 

[TonyChopper]

Thx alot..
How different after u put in the extractor... like got at least 5hp ma?
Then how different again after u replace the 5zigen with toda..
There's another extractor brand Tanabe.. that one good or not?

 

[xxxx]

i've asked N1 last time....they say have to order from japan n have to wait around 1 month.... price is from rm1700 to rm2000....depends....nowadays evrything also more expensive.....

tony, i suggest u get a jasma approved or a japan made one....unless the quality of the custom made is like the ones from japan....
try to get a mugen for b180c....toda is rare too....

 

[hattech-v]

i got 5zigen 4-2-1 last time at RM1K used one.

 

[ace79]

Mmm.. 1 more question.. My piping now is 2 inch straight flow... quite shiok already since removed the cat.. isit necessary to make it 2'3 inch.. my friend say 1.8 car must do 2'3...

2.2 is for 1.6 dohc vtec...so 2.3 would be ok for 1.8 dohc vtec, depends on ur mod also..big hi compression pistons and hi cams..or 2L block..then u need 2.5

HanafyEG, not to shoot you etc, but Omniman's B16A runs a 2.5" pipe, most B16A's ( this is what i learned from most of pals running B16A's and what i learned from B Works, YaYa of USJ VTEC workshop etc, that most VTEC 1.6 runs a 2.3" to 2.5" ) runs 'em as well. Over at US, most LS/VTEC hybrids runs a 3.0" though...hhhmmm...me confused oledi...again...

 

[hattech-v]

heavily mod b16a i think can use 2.5" but standard i think is not recomended...
i've tested it before... :D

 

[zero4]

1.8 i think run with 2.5" better loh, lastt time i using 2.3", the engine like choking like that, now much smoother ler

 

[TODA]

eheh... b16a y cant use 2.5"? if u hardcore enuff 2 convert ur sohc 2 a dohc vtec, y dun push it? get straight pipe 2.5" ............mmmmmm---PAAAAAAAAAAAAA!!!!!!!!!!!!

when u bukak vtec outside neighbours house, u see eggs n tins throwing down but wont kena ur car......LOL

 

[zero4]

eheh... b16a y cant use 2.5"? if u hardcore enuff 2 convert ur sohc 2 a dohc vtec, y dun push it? get straight pipe 2.5" ............mmmmmm---PAAAAAAAAAAAAA!!!!!!!!!!!!

when u bukak vtec outside neighbours house, u see eggs n tins throwing down but wont kena ur car......LOL

eggs was last tiime lah, nowadays they opt for stones, OUCH!!!

 

[ace79]

heavily mod b16a i think can use 2.5" but standard i think is not recomended...
i've tested it before... :D

Omniman's B16A project car was not heavily mod ( RM M22 valvetrain kit, Hondata S2000, 4.785 FD, ATS 1st gear, HyTech 4-2-1 extractor and 2.5" pipe all around, ACT flywheel, Action Clutch 6 puck clutch, standard head, pistons, piston rings and conrods ( mod to suit RM valvetrain kit ) and the car pulled like a train all the way to 9k RPM!

 

[zero4]

2.5" is all goooodddd

 

[xxxx]

ace,
how r u?
long time din hear from u....if u still remeber who am i la...haha
how's ur exhaust system going?

the m22 is considered modded alrdy,
if stock b16a, 2.5 is not so recommended....

 

[ace79]

ace,
how r u?
long time din hear from u....if u still remeber who am i la...haha
how's ur exhaust system going?

the m22 is considered modded alrdy,
if stock b16a, 2.5 is not so recommended....

wei alex "hantu brg 2nd" xxxx! u always log in mehhh, got no homework to do mehh? one day we must go yam char la friend! still looking for a proper muffler lah, i want to go for either RS-R's or maybe RaceCraft CF muffler, dunno lah... ya lah, i'm going to get the M22 as soon as a pal of mine clears up his loan with me ( bought my bike but have yet to settle ) another pal owe me about 3.8k. that could get me a set of custom Titan absorbers all around. i am so confused, the measurement is always taken from the outside or inside of the pipe? both my 5 Zigen extractor and RS - R middle pipe both measured from outside is 2.5", but the inside is 2.3". So when I finally get the Rocket's valvetrain kit, I have to do new piping all around lah! What about my extractor then?

 

[HanafyEG]

HanafyEG, not to shoot you etc, but Omniman's B16A runs a 2.5" pipe, most B16A's ( this is what i learned from most of pals running B16A's and what i learned from B Works, YaYa of USJ VTEC workshop etc, that most VTEC 1.6 runs a 2.3" to 2.5" ) runs 'em as well. Over at US, most LS/VTEC hybrids runs a 3.0" though...hhhmmm...me confused oledi...again...

dont shoot me man, i'm innocent..hehehe...omniman has the flow from the engine (rocket motorsports cams and valvetrain, the rm cams is higher that toda c and jun 3 man) and has to release it quickly i think, so that's why they used 2.5'' pipe..u must remember the engine is a super 1.6, 200whp 1.6..what i meant by using 2.2''pipe is for a stock b16a engine..a 144whp engine..56whp different man..

if u want to build an engine like omniman..do it man, just follow the specs, somemore our fuel is 97 octane....i would like to see a malaysian made 200whp 1.6