Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="gunnerzz" data-source="post: 1064542444" data-attributes="member: 166532">Here it is then..The diagram. This diagram is using multiple capacity cap. The number of caps is up to you, some say more or bigger capacity is better.What u need;-( 4700uf, 16V/12V capacitor ) x 4-( 3300uf, 16V/12V capacitor ) x 4-( 1000uf, 16V/12V capacitor ) x 10-circuit board-box-wires-fuse holder-wire terminal<a href="http://s280.photobucket.com/user/gunnerzz_8094/media/20140714_185221.jpg.html" target="_blank">http://i280.photobucket.com/albums/kk167/gunnerzz_8094/20140714_185221.jpg</a>Sorry for the bad drawing. The basic connection is like in the drawing but u can use your imagination and creativity to place it on the circuit board in order to save space or have the better looking end product. For the fuse holder, u can buy one at any spare part shop.As i discover when i did this in 2008 is that the shop did not have much stock for capacitor so not all VS i made is using the diagram above. This is another design i made using only 4700uf capacitor.<a href="http://s280.photobucket.com/user/gunnerzz_8094/media/20140712_171155.jpg.html" target="_blank">http://i280.photobucket.com/albums/kk167/gunnerzz_8094/20140712_171155.jpg</a>In this design, there is also an LED indicator. Do remember to connect a 1k resistor to the led or it will burnt upon connection of the terminal. I just used normal auto wire in the VS and it works just fine. To make it easier to connect, i also uses the green wire terminal and solder it to the circuit board.If i recalled correctly i made lesser of the VS with multiple capacity capacitor compared with the single capacity capacitor as thats the most commonly sold capacitor. 16V will do fine.</blockquote>

Verification

The Marketplace Latest

original rare spec Rays Volk Racing RE30 15x7jj...
- Started by david tao
- Chassis and Wheels
original rare Rays Volk Racing TE37 SAGA S-Plus...
- Started by david tao
- Chassis and Wheels
original Swift Springs rear strut bar set made in...
- Started by david tao
- Chassis and Wheels
Proton Preve R3 body kit
- Started by jeff6126
- Exterior and Body
Perodua Ativa gear up body kit
- Started by jeff6126
- Exterior and Body
BMW F10 Mperformance front skirt lip
- Started by jeff6126
- Exterior and Body
Honda Civic FC fk7si front bumper set
- Started by jeff6126
- Exterior and Body
brake caliper spray
- Started by jeff6126
- Exterior and Body
BMW F30 M3 bodykit/diffuser set
- Started by jeff6126
- Exterior and Body
Perodua Axia Rahmah bodykit
- Started by jeff6126
- Exterior and Body

Posts refresh every 5 minutes

Boost drop?

My boost used to be 0.8, now by the looks of it, only 0.6.. 0.7 spike then drop to 0.6 bar. What can be the cause?

Basic camshaft installation guide

I've never been a believer of camshafts not because I think they're funny, only because I own an auto car. To make it worse - I'm...

2009 MME Challenger : Altezza from Wing Hin\Trial Tunning.

2009 MME Challenger : Altezza from Wing Hin\Trial Tuning.

Folks,
MME is around the corner and I thought I start this thread to keep upto date in the development of the Altezza track car. Pls feel free to ask...