Reply to thread

See what others are reading now! Try Forums > Current Activity

Message: <blockquote data-quote="aramis" data-source="post: 268423" data-attributes="member: 644">can probably do a custom turbo kit for your car... ;)This is the turbo part list, if you are interested. ;)===============================Turbocharger - (can be small/large whatever you want) some are easier then others. I personally like using T3 and Mitsu turbos. They have worked great for me.Manifold - HF/STD/CX Factory Honda Manifolds can be used with an adapter plate, or you can simply go out and buy a Turbo Manifold from Drag/Greddy/HKS.Adapter Plate - Each plate is a bit differnt depending on the turbocharger, You can simply make this yourself or take it to a machine shop and get one made. I have made 2 styles of plates a T-3 plate and T25/14b plate. Downpipe - This is where picking a good turbocharger gets tough, finding a turbo that has the downpipe exhaust flange aimed in a good spot for the downpipe. (for a smooth bend) Doing test fits are very important, take the exhaust manifold off your car and just set the turbo in the engine bay and visualize how the downpipe can be made. Some turbos are damn near impossible to use. Once you have selected a good turbo, I recommend a 2.5 inch downpipe any decent exhaust shop can do this for you. Mandrel bends are very nice to use also.Intercooler - This is entirely up to you. You dont have to have a intercooler but it keeps the IC temps down a lesser chance of detonation. First take off your front bumper and see how much room you got up their. Take good measurements and visualize where the charge pipes where go. Sometimes alot of cutting/hacking is involved when doing this. The starion/conquest intercooler are great to use for custom projects like this. They can easily be modified and look great! Sometimes they can be a bit tough to find at a decent price. BOV - I highly recommend a BOV, without one you get a really shitty sound. Not only does this sound bad, but once you hit higher levels of boost it will do damage to your turbocharger. Compressor Surge, once the throttle body closes and the charge lines still have pressure they back-feed to the turbocharge and try to spin it backwards. DSM bov's are easy to find, cheap and work great! Just about any BOV will work, even the really inexpensive Bosch BOV's that are very quiet.Brass T - A Brass T will hook up on the back off the block 1/8npt. a 3 way splitter will have to be used. 1 for your stock Oil Pressure Gauge, 1 for your Oil feed line (1/4 barb fitting) and the other to a brass extension from the block. I like to use High pressure line from Napa (350psi Tranny line 5/16) about 4.5 feet you will need. I also flare the fitting on the turbo side and double hose clamp it. For oil return, you will have to install a fitting in your oil pan and create a return line for oil drainage from the turbo. Its pretty easy to do.Coolant lines - For Coolant lines I like to use just normal fuel line. You will need around 7.5 feet total. Also get a couple splitters so you can tap into your cooling sytem somewhere. I like to use the throttle body coolant bypass hoses for this.Charge Pipes - This can be alot of differnt things. Using factory DSM pipes chopped up works really good. Exhaust/Radiator hoses/PVC pipe I have seen alot of things used for this, they all work.Gauges - I recommend at least a boost gauge, but a Air/Fuel gauge is very nice to have, especially when trying to tune your car.Engine Managemnt - Turbocharging a car is not rocket science, Engine management is very important in a good running forced inducted Honda/Acura. This is where I have lacked in my past setups causing alot of blown motors. Best - Standalone Fuel Managment/ AEM EMS / Hondata / Zdyne / Accel DFI / Speedpro / TEC II / Motec / Haltech. and I am sure their are others. Most systems cost over 1000 bucks. Larger injectors are used. Fuel/Spark Maps can be changed anyway you want them. Vtec/Nos control whatever these systems do it all! You can run alot of boost on a stock bottom end with a standalone system, Detonation is not a problem unless you dont know how to tune with them.Good - A rising Rate regulator/larger injectors/ for fuel and MSD 6btm for Spark will let you run a pretty healthy amount of boost on a stock motor. Tuning a system like this can be a bit tricky but it can be done. Check valves or Missing link will also have to be installed to hide boost from the stock ECU, so it does not throw a check engine light.Fair - Rising rate regulator on Stock injectors with nothing else will let you run around 5-7psi. I would keep a close eye on your air/fuel gauge to make sure your not detonating.None - It can be done, but not recommend at all. Back your timing down a few degrees, get 1 step colder plugs, buy high oct fuel all the time, a large front mount IC will be needed. Run a maxium of 5 psi.</blockquote>

Verification

The Marketplace Latest

original Swift Springs rear strut bar set made in...
- Started by david tao
- Chassis and Wheels
Proton Preve R3 body kit
- Started by jeff6126
- Exterior and Body
Perodua Ativa gear up body kit
- Started by jeff6126
- Exterior and Body
BMW F10 Mperformance front skirt lip
- Started by jeff6126
- Exterior and Body
Honda Civic FC fk7si front bumper set
- Started by jeff6126
- Exterior and Body
brake caliper spray
- Started by jeff6126
- Exterior and Body
BMW F30 M3 bodykit/diffuser set
- Started by jeff6126
- Exterior and Body
Perodua Axia Rahmah bodykit
- Started by jeff6126
- Exterior and Body
Nissan Almera Tomei body kit
- Started by jeff6126
- Exterior and Body
original rare Black Racing Pro N1 16x6.5jj offset...
- Started by david tao
- Chassis and Wheels

Posts refresh every 5 minutes

Looking for a GT-R33 (400R type) Front bumper

Hi guys,

Anybody has a 400R bumper for sale or know where i can find one in KL ? Because this afternoon had a light accident and my bumper is gone.

Thanks !!

Fuel Magnet For Fuel Saving

Here is a interesting site..
http://www.emanator.demon.co.uk/bigclive/magnet.htm

There are a lots of product like this available outside anyone of u out there tried? Is there any effect?
Does anyone here DIY this...

Cold Air Intake

Hi guys,
does any of you did a cold air intake for carburator? I am using satria 1.3 and just wanted to try can do or not.
Does anyone know?

Search

Enjoying Zerotohundred?

Log-in for an ad-less experience

Reply to thread

The Marketplace Latest

original Swift Springs rear strut bar set made in...

Proton Preve R3 body kit

Perodua Ativa gear up body kit

BMW F10 Mperformance front skirt lip

Honda Civic FC fk7si front bumper set

brake caliper spray

BMW F30 M3 bodykit/diffuser set

Perodua Axia Rahmah bodykit

Nissan Almera Tomei body kit

original rare Black Racing Pro N1 16x6.5jj offset...

Posts refresh every 5 minutes

Recent Posts

Darker Design : Mercedes-Benz Launches GLA Nightfall Edition in Malaysia

Honda Malaysia Doubles Down on Hybrids: New CR-V Launches with Dual e:HEV...

BateriHub Reaches 200-Store Milestone, Becomes Malaysia’s Largest...

Been stalking for 3 years edy

Recommendation: Turbocharger for 4B11 N.A engine

Search

Online now

Enjoying Zerotohundred?